features regulated converters ? 2:1 wide input voltage range ? 1.6kvdc isolation ? ul certifed ? effciency up to 87% ? fixed operating frequency ? six-sided continuous shield pd-1 rev.: 1/2016 www.recom-power.com dc/dc converter 3 y e a r w a r r a n t y 3 description the rp10-e series dc/dc converters are certifed to ul 60950-1 and cul 60950-1. this makes them ideal for all telecom and industrial applications where approved safety standards are required. the industry standard 2 x 1 package meets military standards for thermal shock and vibration tolerance and is available with an optional remote on/off control pin. this series is also available with the /m1 and /m2 option which is particularly suitable for extended temperature range applications. e196683 10 watt 2 x 1 single & dual output rp10-e selection guide part number input output output input (1) effciency (1) max. capacitive voltage range voltage current current typ. load (2) [vdc] [vdc] [ma] [ma] [%] [f] rp10-123.3se (3,4) 9-18 3.3 2000 688 80 6800 rp10-1205se (3,4) 9-18 5 2000 1029 81 4700 rp10-1212se (3,4) 9-18 12 830 988 84 690 rp10-1215se (3,4) 9-18 15 670 997 84 470 rp10-243.3se (3,4) 18-36 3.3 2000 344 80 6800 rp10-2405se (3,4) 18-36 5 2000 508 82 4700 rp10-2412se (3,4) 18-36 12 830 494 84 690 rp10-2415se (3,4) 18-36 15 670 499 84 470 rp10-483.3se (3,4) 36-75 3.3 2000 172 80 6800 rp10-4805se (3,4) 36-75 5 2000 248 84 4700 rp10-4812se (3,4) 36-75 12 830 241 86 690 rp10-4815se (3,4) 36-75 15 670 241 87 470 RP10-1205DE (3,4) 9-18 5 1000 992 84 680 rp10-1212de (3,4) 9-18 12 416 1002 83 330 rp10-1215de (3,4) 9-18 15 333 991 84 110 rp10-2405de (3,4) 18-36 5 1000 502 83 680 rp10-2412de (3,4) 18-36 12 416 489 85 330 rp10-2415de (3,4) 18-36 15 333 496 84 110 rp10-4805de (3,4) 36-75 5 1000 248 84 680 rp10-4812de (3,4) 36-75 12 416 242 86 330 rp10-4815de (3,4) 36-75 15 333 245 85 110 ul60950-1 certifed input voltage output voltage s ingle or d ual rp10-__ __ _e/_ _ ordering expamples: rp10-1205se/p = 12v input, 5v output, standard temp. range, positive logic ctrl pin ftted rp10-4805de/m1-hc = 48v input, 5v output, extended temp. range, no ctrl pin, heat-sink ftted model numbering notes: note3: add suffx m1 for higher effciencies and extended temperature range add suffx p for ctrl function with positive logic (1=on, 0=off) add suffx n for ctrl function with negative logic (0=on, 1=off) note4: add suffx -hc for premounted heat-sink and clips package (4) control logic (3) notes: note1: maximum value at nominal input voltage and full load. note2: test by minimum vin and constant resistor load.
basic characteristics parameter condition min. typ. max. input voltage range nom. vin = 12v nom. vin = 24v nom. vin = 48v 9vdvc 18vdc 36vdc 12vdc 24vdc 48vdc 18vdc 36vdc 75vdc under voltage lockout (uvlo) none input filter pi-type input refected ripple current (5) nominal vin and full load 30map-p input surge voltage 12v input, 100ms max. 24v input, 100ms max. 48v input, 100ms max. 36vdc 50vdc 100vdc start-up time nominal vin and constant resistor load power up 20ms operating frequency range 270khz 300khz 330khz minimum load (6) of full load 10% ripple and noise measured by 20mhz bandwidth single dual 50mvp-p 75mvp-p remote on/off (7) positive logic dc-dc on dc-dc off open or 3.5v < vr < 12v short or 0v < vr < 1.2v negative logic dc-dc on dc-dc off short or 0v < vr < 1.2v open or 3.5v < vr < 12v input current of remote pin (ctrl) dc-dc off 20ma dc-dc on -0.5ma +1.0ma continued on next page pd-2 rev.: 1/2016 www.recom-power.com dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted rp10-e series notes: note5: simulated source impedance of 12h. 12h inductor in series with +vin. note6: the rp10 (w) series required a minimum 10% loading on the output to maintain specifed regulation. operation under no-load condition will not damage these devices, however they may not meet all listed specifcation. note7: the on/off control function can be positive or negative logic. the pin voltage is referenced to -vin pin. if no suffx is specifed, the control pin will be omitted. effciency vs. output current effciency vs. input voltage 9vin 12vin 18vin efficiency [%] output current [%] 10 55 50 45 40 60 65 70 75 80 85 95 90 20 30 40 50 60 70 80 90 100 efficiency [%] total input voltage [%] 9 55 60 65 70 75 85 11 12 14 16 18 10 13 15 17 80 rp10-1205se
dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted regulations parameter condition value output voltage accuracy 1% line voltage regulation low line to high line 0.2% load voltage regulation 0% to 100% load single dual 0.5% 1.0% cross regulation asymmetrical 25%<>100% load 5% transient response recovery time 25% load step change 250 s typ. rp10-e series pd-3 rev.: 1/2016 www.recom-power.com effciency vs. output current effciency vs. output current effciency vs. input voltage effciency vs. input voltage 18vin 24vin 36vin efficiency [%] output current [%] 10 60 55 50 45 40 65 70 75 80 90 95 20 40 60 80 100 30 50 70 90 85 36vin 48vin 75vin efficiency [%] output current [%] 10 60 55 50 45 40 65 70 75 80 95 90 20 40 60 80 100 30 50 70 90 85 efficiency [%] total input voltage [%] 18 60 65 70 75 80 90 22 24 28 32 36 20 26 30 34 85 efficiency [%] total input voltage [%] 36 74 76 78 80 82 86 44 48 56 66 75 40 52 60 72 84 rp10-2405se rp10-4805se
pd-4 rev.: 1/2016 www.recom-power.com dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted rp10-e series environmental parameter condition value operating temperature range (reference derating curve) (9) standard m1 with derating with derating -25c to +100c -40c to +85c maximum case temperature +105c temperature coeffcient 0.02%/c max. thermal impedance vertical direction by natural convection (20lfm) without heat-sink with heat-sink 12c/watt 10c/watt operating humidity non-condensing 5% - 95% rh thermal shock mil-std-810f vibration mil-std-810f mtbf (10) mil-hdbk-217f, full load 3342 x10 3 hours continued on next page -25 60 77 80 100 40 20 0 -20 0 20 40 60 80 100 ambient temperature [c] output power [%] -25 60 81 80 100 40 20 0 -20 0 20 40 60 80 100 ambient temperature [c] output power [%] derating graph (9,11) protections parameter condition value short circuit protection (scp) continuous, automatic recovery over voltage protection (ovp) zener diode clamp 3.3vout 5vout 12vout 15vout 3.9vdc typ. 6.2vdc typ. 15vdc typ. 18vdc typ. over load protection (olp) % of iout rated 150% max. isolation voltage i/p to o/p i/p (o/p) to case 1.6kvdc/1 minute 1.6kvdc/1 minute isolation resistance 500vdc 1g ? min. isolation capacitance 300pf max. rp10-4805se rp10-4805se with heat-sink notes: note8: this power module is not internally fused. an input line fuse must always be used.
safety and certifications certifcate type (safety) report / file number standard ul general safety e196683 ul60950-1 1st ed.: 2003 c22.2 no. 60950 1st. ed.: 2003 emc compliance condition standard / criterion emi standard (12) with external flter en55022, class a or b esd radiated immunity fast transient (13) surge (13) conducted immunity air 8kv and contact 6kv 10 v/m 2kv 2kv 10 vr.m.s en61000-4-2, criteria b en61000-4-3, criteria a en61000-4-4, criteria b en61000-4-5, criteria b en61000-4-6, criteria a continued on next page dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted rp10-e series pd-5 rev.: 1/2016 www.recom-power.com -40 60 85 80 100 40 20 0 -20 0 20 40 60 80 100 ambient temperature [c] output power [%] -40 60 88 80 100 40 20 0 -20 0 20 40 60 80 100 ambient temperature [c] output power [%] notes: note9: m1 version is more effcient, therefore, it can be operated in a more extensive temperature range than standard version. note10: bellcore tr-nwt-000332. case i: 50% stress, temperature at 40oc. (ground fxed and controlled environment). note11: derating graphs are valid only for the shown part numbers. if you need detailed derating-information about a part- number not shown here please contact our technical support service at techsupportat@recom-power.com. notes: note12: the standard modules meet emi class a or class b with external components, see flter suggestions below. note13: an external input flter capacitor is required if the module has to meet en61000-4-4, en61000-4-5. the flter capacitor recom suggests: nippon chemi-con ky series, 220f/100v. rp10-4805se/m1-hc rp10-4805se/m1 input input dc dc fuse c1 +v in +v out -v out -v in load c3 c2 c2 dc dc fuse c1 +v in +v out com -v out -v in load load c3 input input dc dc fuse c1 +v in +v out -v out -v in load c3 c2 c2 dc dc fuse c1 +v in +v out com -v out -v in load load c3 model c1 c2 c3 rp10-12xxs_de 2.2f/25v 1206 mlcc 1000pf/2kv 1808 mlcc 1000pf/2kv 1808 mlcc rp10-24xxs_de n/a 1000pf/2kv 1808 mlcc 1000pf/2kv 1808 mlcc rp10-48xxs_de n/a 1000pf/2kv 1808 mlcc 1000pf/2kv 1808 mlcc emi filtering class a
pd-6 rev.: 1/2016 www.recom-power.com dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted rp10-e series dimensions and physical characteristics parameter type value material case base potting nickel coated copper non-conductive black plastic epoxy (ul94-v0) package dimensions (lxwxh) without heat-sink with heat-sink 50.8 x 25.4 x 10.2mm 56.8 x 25.4 x 16.8mm package weight without heat-sink with heat-sink 27g 37.89g continued on next page dimension drawing (mm) 25.4 5.60 10.2 50.8 ? 1.0 2 4 bottom view 23 5 3 5.10 15.20 20.30 2.50 10.20 10.20 12.70 1 pin connections pin # single dual 1 +vin +vin 2 -vin -vin 3 +vout +vout 4 no pin com 5 -vout -vout 6 ctrl ctrl pin pitch tolerance 0.25mm pin dimension tolerance 0.1mm xx.x 0.5mm xx.xx 0.25mm input input dc dc fuse c2 c1 +v in +v out -v out -v in load c4 c3 +v out com -v out load load l1 dc dc fuse c2 c1 +v in +v out -v out -v in c4 c3 l1 input input dc dc fuse c2 c1 +v in +v out -v out -v in load c4 c3 +v out com -v out load load l1 dc dc fuse c2 c1 +v in +v out -v out -v in c4 c3 l1 emi filtering class b model c1 c2 c3/c4 l1 rp10-12xxs_de 3.3f/50v 1812 mlcc n/a 1000pf/2kv 1808 mlcc cmc: 325h ref: we 744290321 ref.: cmc-06 rp10-24xxs_de 2.2f/50v 1812 mlcc n/a 1000pf/2kv 1808 mlcc cmc: 325h ref: we 744290321 ref.: cmc-06 rp10-48xxs_de 2.2f/100v 1812 mlcc 2.2f/100v 1812 mlcc 1000pf/2kv 1808 mlcc cmc: 325h ref: we 744290321 ref.: cmc-06
packaging information parameter type value packaging quantity without heat-sink with heat-sink tube tray 9pcs. 20pcs. storage temperature range -55c to +125c storage humidity 5% - 95% rh the product information and specifcations are subject to change without prior notice. recom products are not authorized for use in safety-critical applications (such as life support) without recoms explicit written consent. a safety-critical application is defned as an application where a failure of a recom product may reasonably be expected to endanger or cause loss of life, infict bodily harm or damage property. the buyer shall indemnify and hold harmless recom, its affliated companies and its representatives against any damage claims in connection with the unauthorized use of recom products in such safety-critical applications. dimension drawing (mm) with heat-sink 10.2 16.8 20.30 56.80 15.20 25.4 5.6 5.10 2.50 ?1.0 24.20 50.00 5.85 1.40 1.30 1.95 1.30 top view heat-sink dc/dc converter specifcations measured at ta = 25c, nominal input voltage, full load otherwise noted rp10-e series pd-7 rev.: 1/2016 www.recom-power.com
|
